Four Undertow forms carry a continuous raised wave pattern from the elongated base shape to the topper, grounded by a black marble disc.
Made to order. Designed and assembled in Denver.
Overall: 27.5 in high × 7.0 in wide × 6.5 in deep.
Base: 6.0 in diameter × 1.0 in high. Opal spine: 24.0 in long × 1.5 in diameter.
Overall dimensions include the complete shape envelope and exclude the cord.
Measurements are approximate and rounded up to the nearest 0.5 inch.
From the base upward: Undertow Pitt Medium, Chonk Medium, Tantrum Medium and Spill Topper. All shapes are in Canvas.
Plug-in fixture with an opal spine.
Each shape is 3D printed in Canvas Marble PETG, with a pale warm-grey tone and fine warm-taupe speckle. Fine layer lines and subtle variations are part of the printing process.
The modular shapes connect with a twist-lock system. You can swap or rearrange compatible pieces while keeping the fixture’s required fit and clearances. Before making changes, switch off and allow the fixture to cool; unplug plug-in fixtures or switch off power at the circuit breaker for hardwired fixtures. Follow the assembly instructions for your fixture, and never force a connection or alter the electrical components.
Place on a stable, level surface in a dry indoor space. Keep away from radiators, fireplaces, stoves and other heat sources. Avoid prolonged direct sunlight and locations where heat builds up, such as a hot window ledge or enclosed sunroom. Excessive heat may soften or distort the printed shapes. Keep away from water, splashes, steam and condensation. Do not use outdoors or in wet or damp locations. Do not drape fabric or other objects over the fixture.
Before cleaning, switch off and allow the fixture to cool; unplug plug-in fixtures or switch off power at the circuit breaker for hardwired fixtures. Dust gently with a soft, dry cloth. Avoid solvents, abrasive cleaners and scrubbing. Do not sand, drill or heat the printed shapes. If a shape cracks, warps or no longer locks securely, stop using the fixture and contact the studio before using it again.
Four Undertow forms carry a continuous raised wave pattern from the elongated base shape to the topper, grounded by a black marble disc.
Made to order. Designed and assembled in Denver.
Overall: 27.5 in high × 7.0 in wide × 6.5 in deep.
Base: 6.0 in diameter × 1.0 in high. Opal spine: 24.0 in long × 1.5 in diameter.
Overall dimensions include the complete shape envelope and exclude the cord.
Measurements are approximate and rounded up to the nearest 0.5 inch.
From the base upward: Undertow Pitt Medium, Chonk Medium, Tantrum Medium and Spill Topper. All shapes are in Canvas.
Plug-in fixture with an opal spine.
Each shape is 3D printed in Canvas Marble PETG, with a pale warm-grey tone and fine warm-taupe speckle. Fine layer lines and subtle variations are part of the printing process.
The modular shapes connect with a twist-lock system. You can swap or rearrange compatible pieces while keeping the fixture’s required fit and clearances. Before making changes, switch off and allow the fixture to cool; unplug plug-in fixtures or switch off power at the circuit breaker for hardwired fixtures. Follow the assembly instructions for your fixture, and never force a connection or alter the electrical components.
Place on a stable, level surface in a dry indoor space. Keep away from radiators, fireplaces, stoves and other heat sources. Avoid prolonged direct sunlight and locations where heat builds up, such as a hot window ledge or enclosed sunroom. Excessive heat may soften or distort the printed shapes. Keep away from water, splashes, steam and condensation. Do not use outdoors or in wet or damp locations. Do not drape fabric or other objects over the fixture.
Before cleaning, switch off and allow the fixture to cool; unplug plug-in fixtures or switch off power at the circuit breaker for hardwired fixtures. Dust gently with a soft, dry cloth. Avoid solvents, abrasive cleaners and scrubbing. Do not sand, drill or heat the printed shapes. If a shape cracks, warps or no longer locks securely, stop using the fixture and contact the studio before using it again.
