Five Undertow pendants repeat three complementary silhouettes along a linear canopy. Raised waves connect the forms, with independently adjustable drops to set the rhythm.
Shipping included.
Dimensions
Canopy: 36.0 in long × 6.0 in wide × 1.0 in deep. Height per pendant: 16.0 in. Maximum pendant width: 5.5 in. 6.0 ft cord per pendant; drops adjust independently. Approximate measurements, rounded up to the nearest 0.5 inch.
Shape composition
All shapes share the selected filament color.
Port 1: Undertow Pitt Small, Undertow Chonk Small, Undertow Spill Topper.
Port 2: Undertow Pitt Small, Undertow Hennin Small, Undertow Spill Topper.
Port 3: Undertow Pitt Small, Undertow Tantrum Small, Undertow Tantrum Topper.
Port 4: Undertow Pitt Small, Undertow Hennin Small, Undertow Spill Topper.
Port 5: Undertow Pitt Small, Undertow Chonk Small, Undertow Spill Topper.
Lighting
Hardwired fixture with 5 T30 E26 LED bulbs.
6.0 ft cord per pendant; drops adjust independently.
Materials & Modularity
Each shape is 3D printed in the selected filament. Material composition varies by color. Fine layer lines and subtle variations are part of the printing process.
The modular shapes connect with a twist-lock system. You can swap or rearrange compatible pieces while keeping the fixture’s required fit and clearances. Before making changes, switch off and allow the fixture to cool; unplug plug-in fixtures or switch off power at the circuit breaker for hardwired fixtures. Follow the assembly instructions for your fixture, and never force a connection or alter the electrical components.
Placement & Care
For dry indoor use. Keep away from radiators, fireplaces, stoves and other heat sources. Avoid prolonged direct sunlight and locations where heat builds up, such as a hot window ledge or enclosed sunroom. Excessive heat may soften or distort the printed shapes. Keep away from water, splashes, steam and condensation. Do not use outdoors or in wet or damp locations. Do not drape fabric or other objects over the fixture.
Before cleaning, switch off and allow the fixture to cool; unplug plug-in fixtures or switch off power at the circuit breaker for hardwired fixtures. Dust gently with a soft, dry cloth. Avoid solvents, abrasive cleaners and scrubbing. Do not sand, drill or heat the printed shapes. If a shape cracks, warps or no longer locks securely, stop using the fixture and contact the studio before using it again.
Specifications & installation
Five Undertow pendants repeat three complementary silhouettes along a linear canopy. Raised waves connect the forms, with independently adjustable drops to set the rhythm.
Shipping included.
Dimensions
Canopy: 36.0 in long × 6.0 in wide × 1.0 in deep. Height per pendant: 16.0 in. Maximum pendant width: 5.5 in. 6.0 ft cord per pendant; drops adjust independently. Approximate measurements, rounded up to the nearest 0.5 inch.
Shape composition
All shapes share the selected filament color.
Port 1: Undertow Pitt Small, Undertow Chonk Small, Undertow Spill Topper.
Port 2: Undertow Pitt Small, Undertow Hennin Small, Undertow Spill Topper.
Port 3: Undertow Pitt Small, Undertow Tantrum Small, Undertow Tantrum Topper.
Port 4: Undertow Pitt Small, Undertow Hennin Small, Undertow Spill Topper.
Port 5: Undertow Pitt Small, Undertow Chonk Small, Undertow Spill Topper.
Lighting
Hardwired fixture with 5 T30 E26 LED bulbs.
6.0 ft cord per pendant; drops adjust independently.
Materials & Modularity
Each shape is 3D printed in the selected filament. Material composition varies by color. Fine layer lines and subtle variations are part of the printing process.
The modular shapes connect with a twist-lock system. You can swap or rearrange compatible pieces while keeping the fixture’s required fit and clearances. Before making changes, switch off and allow the fixture to cool; unplug plug-in fixtures or switch off power at the circuit breaker for hardwired fixtures. Follow the assembly instructions for your fixture, and never force a connection or alter the electrical components.
Placement & Care
For dry indoor use. Keep away from radiators, fireplaces, stoves and other heat sources. Avoid prolonged direct sunlight and locations where heat builds up, such as a hot window ledge or enclosed sunroom. Excessive heat may soften or distort the printed shapes. Keep away from water, splashes, steam and condensation. Do not use outdoors or in wet or damp locations. Do not drape fabric or other objects over the fixture.
Before cleaning, switch off and allow the fixture to cool; unplug plug-in fixtures or switch off power at the circuit breaker for hardwired fixtures. Dust gently with a soft, dry cloth. Avoid solvents, abrasive cleaners and scrubbing. Do not sand, drill or heat the printed shapes. If a shape cracks, warps or no longer locks securely, stop using the fixture and contact the studio before using it again.
Specifications & installation
Image 1 of 73
Image 2 of 73
Image 3 of 73
Image 4 of 73
Image 5 of 73
Image 6 of 73
Image 7 of 73
Image 8 of 73
Image 9 of 73
Image 10 of 73
Image 11 of 73
Image 12 of 73
Image 13 of 73
Image 14 of 73
Image 15 of 73
Image 16 of 73
Image 17 of 73
Image 18 of 73
Image 19 of 73
Image 20 of 73
Image 21 of 73
Image 22 of 73
Image 23 of 73
Image 24 of 73
Image 25 of 73
Image 26 of 73
Image 27 of 73
Image 28 of 73
Image 29 of 73
Image 30 of 73
Image 31 of 73
Image 32 of 73
Image 33 of 73
Image 34 of 73
Image 35 of 73
Image 36 of 73
Image 37 of 73
Image 38 of 73
Image 39 of 73
Image 40 of 73
Image 41 of 73
Image 42 of 73
Image 43 of 73
Image 44 of 73
Image 45 of 73
Image 46 of 73
Image 47 of 73
Image 48 of 73
Image 49 of 73
Image 50 of 73
Image 51 of 73
Image 52 of 73
Image 53 of 73
Image 54 of 73
Image 55 of 73
Image 56 of 73
Image 57 of 73
Image 58 of 73
Image 59 of 73
Image 60 of 73
Image 61 of 73
Image 62 of 73
Image 63 of 73
Image 64 of 73
Image 65 of 73
Image 66 of 73
Image 67 of 73
Image 68 of 73
Image 69 of 73
Image 70 of 73
Image 71 of 73
Image 72 of 73
Image 73 of 73